4. SUPER BOTTOM PROTECT - HIGH BUILD EPOXY PRIMER (2 PART KIT)

Item #
2044
Price
$129.95
Sale Price
$99.95
You Save
You Save: 23%
Options
Quantity:
  • Description

SUPER BOTTOM PROTECT - HIGH BUILD EPOXY PRIMER (2 PART KIT)



Super Bottom Protect 2 part high build epoxy primer gelcoat blister repair system provides a seamless epoxy coating that creates a high build water barrier that eliminates any direct path for water migration. Super Bottom Protect 2 part high build epoxy primer is a heavy duty 3:1 epoxy paint coating for boats that prevents water absorption and blistering on fiberglass boat hulls.
 

  • PREVENT WATER ABSORPTION AND BLISTERING
  • ELIMINATED DIRECT PATH FOR WATER MIGRATION
  • HEAVY DUTY 3:1 EPOXY COATING
  • EXCELLENT ANTI-CORROSIVE SUBSTRATE PRIMER FOR METALS
  • FULL MULTI-SEASON PROTECTION


4-5 coats of the marine epoxy primer is recommended for best application for gelcoat blistering protection.

TECHNICAL DATA FOR SUPER BOTTOM PROTECT

SUGGESTED USES Prevention and repair of gelcoat blistering

COLORS Super Bottom Protect PART A / PART B Gray

FINISH: Matte

VEHICLE TYPE: Epoxy Resin

SOLVENT TYPE: High Flash Naphtha

VOC: 330 grams / liter

SOLIDS BY WEIGHT: 50%

WEIGHT PER GALLON: 11 lbs. per gallon

RECOMMENDED DRY FILM: 10.0 mils

COVERAGE: Approximate coverage at two mils dry is 400 square feet per gallon, and recommended thickness of 10 mils dry would require 4-5 full coats. Material losses during mixing and application will vary and must be taken into consideration.

VISCOSITY AT 75°F (24°C): 70-80 KU

AVERAGE DRY TIME 75°F (23° C):

Dries to touch in 2 hours. Faster dry times in temperatures over 75° degrees F, and slower dry times in temperatures cooler than 75° degrees F. You can re-coat with Super Bottom Protect marine epoxy primer with self in 2 hours to 48 hours. After 48 hours, you MUST sand with 80 grit sandpaper before re-coating with another coat of Super Bottom Protect Primer. When over-coating with anti-fouling, allow 2 hours minimum to 4 hours maximum. Faster dry times in temperatures over 75° degrees F, and slower dry times in temperatures cooler than 75° degrees F. After 4 hours, you MUST sand with 80 grit sandpaper before application of anti-fouling paint, or apply another coat of Super Bottom Protect Primer and overcoat with the appropriate anti-fouling paint within the 2-4 hour over coat window.

VERY IMPORTANT:

Application of anti-fouling over Super Bottom Protect Primer marine epoxy primer is critical. Anti-fouling may be applied directly over the marine paint by using the “thumb print” method. Touch the Super Bottom Protect Primer film with your thumb – if the paint does not get on your thumb, but is tacky and you can make a thumb print, you are properly in the “overcoat window.” You can then apply anti-fouling paint. If the paint gets on your thumb, it is too soon to recoat with anti-fouling paint. If you can’t leave a thumb print, you have missed the "overcoat window" & MUST sand with 80 grit sandpaper or apply another coat of the marine primer paint and then re-coat as above. For Vinyl anti-fouling overcoat times, contact us directly.

WHEN OVER-COATING SUPER BOTTOM PROTECT SEALER:

Apply Super Bottom Protect Sealer per label directions. Dries to touch in 5 hours. After last coat of Super Bottom Protect Sealer, wash surface thoroughly with fresh water, wait 12 hours minimum, sand surface with 80 grit paper, wipe surface with tack cloth, apply first coat of Super Bottom Protect Primer.

RECOMMENDED REDUCER: Reduce with a reducer as needed for proper flow and performance, 10% maximum.

RECOMMENDED CLEAN UP: Use a Reducer

RECOMMENDED FINISH: Ablative anti-foulings

SURFACE PREPARATION: BARE FIBERGLASS: Degrease by wiping with a rag soaked in a dewaxer. Sand with 80 grade (grit) paper. Remove sanding residue. Wipe with a dewaxer.

Over Super Bottom Protect PART A / PART B: Wash with soap and water. Rinse with fresh water and allow to dry. Sand with 80 grade (grit) paper. Remove sanding residue. Wipe with a dewaxer.

BARE METAL

Surface should be blasted to bright metal. Remove all blast or sanding residue using a clean air line and sweeping with a clean brush or broom. Vacuum clean for best results. Apply primer within 1 hour of metal preparation. If blasting is not possible (or if more than 2 hours has passed since blasting) sand or grind with coarse emery cloth and apply a dewaxer prior to Super Bottom Protect PART A / PART B.

APPLICATION

Apply enough Super Bottom Protect PART A / PART B to reach a final Dry Film Thickness of 10mils. This usually takes 4-5 coats but the amount of paint is more important than the number of coats.

Airless Spray Pressure: 165 bar/2400 psi Tip Size: 0.44-0.53 mm/17-21 thou.

Conventional Spray Pressure Pot: Pressure: 3.44-4.47 bar/50-65 psi (gun pressure); 10-15 psi (pot pressure). Tip Size: 1.5-1.8 mm/60-70 thou. Siphon Cup: Pressure: 3.44-4.47 bar/50-65 psi - gun pressure. Tip Size: 1.8-2.2 mm/70-85 thou.

Brush Use a natural bristle brush.

Roller Use a 3/8” - 1/2” nap solvent resistant roller.

POT LIFE: 5 hours

LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 50F or above 95F. Do not put over 1 part paints.

SHELF LIFE: Minimum 24 months

MIXING: Mix PART A Super Bottom Protect Base and PART B Curing Agent at the specified ratio of 3 parts (whole can) PART A Base and 1 Part (whole quart) PART B Activator. Mix small amounts until application technique is developed.

PACKAGE: 1 Gallon Kit (3/4 gallon PART A Base, 1 quart PART B Activator)

eCommerce software powered by SolidCactusEcommerce